Видео

Just used mine this weekend. They are hell for stout!!

Buy a rebuild kit for the deck. $150 and you are done for a while.

And actually I think you can go get a whole new aftermarket stamped deck for that mower for really cheap as well... like 80 bucks or something... The original Cub cadet though is stupid priced like seven or eight $900... So with the price of all the pulleys spindles blades belts and a new stamp deck you're still going to be around $200 or less...

I'm thinking your prop shear pin is sheared and your prop isn't able to push the boat. There's often enough friction to spin prop, but not enough under a load. Nice project by yhe way. That motor will move that boat around 9 knots

I sprayed latex with the same gun, just like any paint that going to be sprayed through a hvlp you need to thin it down and upgrade your reservoir to the spectrum paint canister system, I did a 20% mix regular water works fine.

Can you just buy 1x2

It’s not necessary to count turns turn it all the way in back it out 1 1/2 turns and you’re good to go

Wish you could make me one! I'd buy it

Do you have any plans for. Building

I’d delete this video if I was you, what an absolute waste of time this video is.

This "lawn decoration" would look great with a flower garden planted in it. When do you plan to modify everything about this "boat" and build it out of "sea worthy" materials and construction techniques? At least use plywood that is thicker than paneling and use something other than staples to hold it together. The only thing you did "right" was flashing the seams, although you should have floated those edges.

Thanks for the video, just what I needed, especially the min/max weight of the Stays. Which type of hinge were you using?

Good video! I bought the Bauer band saw for my son, and later was able to get the mounting stands for both of us. I also bought me a Hercules saw and did not have the problems you did with the trigger. However, the last little part of your video addresses my problem with the saw cutting straight vertically. :)

A couple things. Usually, although the spindles are greasable, the bearings inside have plastic covers which don't allow the grease to enter. The fix is to disassemble the spindle and remove the seals. Also, due to the bent deck and weld bead, it's important to confirm that the blade tips are actually even with each other to result in a even cut.

مرحبا بك في الجزائر

bisa di lampirkan untuk lebar atas dan lebar bawah perahu dan berapa ketinggian dan panjang perahu yang anda buat

Dosent always work- if it’s out of ink, it’s out of ink… no matter what you do to it- other than adding more ink- ya can’t get blood from a turnip

Agregar medidas y materiales

Mostly well done. Bird boxes should have a predator block over the access hole to prevent predators from reaching in and taking eggs or chicks. There should also be 3-4 kerf cuts below the acess hole both out side and inside. These allow easy acess and allows chicks to climb out when they fledge

if you aint modifying your tools, you aint living ! well done : )

I knew it! We've been doing this in my elementary days

Nice job!

I had one when I was in the Boy Scouts.

nope

Nice video. Great shots. Cool holster.❤

How are you cooling your laser tube? Are you using just deionized water, or have you added anything else instead?

so much easier to use than the new models in a lot of situatiions

I tried doing this on our floor standing lamp. The stands and the shelves are all metal. Touching the metal ring attached to that little black box turns the lamp on and off etc. But attaching this ring to the lamp stands does nothing unfortunately.

Es de esas gentes que hacen las cosas y sedan mucho taco son tacones idiots

Directly from Hannu's Boatyard plans ?

Do you think it could support 20 lbs?

When you do nonsense instead of buying a powerbank Power Delivery.

I realize your video was yrs ago.. but I have the same brush cutter.. only difference is the muffler.. but got it running and fuel leaking same way.. funny had a hell of a time removing grease gun from fitting..funny.. but your video is what I needed to so I can get mine going.. thank you

I wish you were my neighbor lmao

how to buy,,it is available here in dubai?

You don't need $2,000.00 worth of tools to make this. A handsaw, hammer and nails and a cheap drill with a hole saw are all that is really needed.

Question: When you replaced the trigger assembly with a new assembly you pointed out that it worked, but still leaked air. I'm curious if your self-repaired/modified assembly leaked air when you reassembled it. Thanks for the video. Yes, it was interesting.

How much Ford the New One?

Shouldn't you at least clean the spark plug, might help, just saying?

i just came across an old Lightwin and did not really know where to start, but this video is a great help. Thanks

You didn't mention the percent alcohol, is the % of alcohol insignificant?

I would try reducing the fan size.

Entertaining to watch. But as a beginner wanting to build my first birdhouse, a video showing how to do it using $2,000 worth of woodworking equipment and tools isn't very relevant. Thanks.

Nice video. Cool display. Killer paint job. Mahalo for sharing! : )

I'm curious what software you have with your X-Carve? I just got one, and am learning how to use it. I bought V Carve Desktop, and must say I am not impressed with it. For 350 dollars, you can do no 3-D modelling with it (except for canned clipart) and it won't generate toolpaths for small bits (less than 1/8 inch) to give fine detail to your carvings. I am guessing they want to goad you into buying the VCarve Pro for another 350 dollars. But it makes me wonder what THAT version left out, trying to get you to buy Aspire for two grand.

All depends on the Thinning and work from there i have done many doors Latex and it comes out find Glossy as.

2k Basecoat or Enamel Gloss Oil Based my Psi is 25 depending on the Compressor if using Clear Coat Psi 30 just need to paly around myself have it down put now.

Thin it more and get closer to the cardboard

So that is water based paint as if using Oil Gloss enamel would need Turps.

Watching this as a teacher 😂